Kitchen Ventilation Explained: Sizing and Installing a Range Hood
Cooking produces more than aromas. Heat, moisture, grease particles and, with gas burners, combustion byproducts all rise from the cooktop and spread through the house if nothing removes them. A range hood is the kitchen’s dedicated ventilation system. How it is selected and installed affects indoor air quality, the cleanliness of cabinets and walls, and even how the rest of the house’s mechanical systems behave.
Ducted Versus Recirculating Hoods
A ducted hood moves air outside through a duct. A recirculating, or ductless, hood pulls air through grease filters and usually a charcoal filter, then returns it to the kitchen. Charcoal reduces odors, but a recirculating hood does not remove heat, humidity or combustion gases from the house.
Wherever an exterior duct route exists, ducted ventilation is the more effective option. Recirculating units are usually reserved for situations where ducting is impossible, such as some interior islands or buildings with restrictions.
Airflow: Understanding CFM
Hood airflow is rated in cubic feet per minute (CFM):
- Gas ranges: a frequently cited rule of thumb is about 100 CFM for every 10,000 BTU of total burner output.
- Electric cooktops: sizing is often based on cooktop width.
- Island hoods: these lack the surrounding walls and cabinets that help contain rising smoke, so they generally need more airflow than wall-mounted hoods over the same cooktop.
Higher CFM is not automatically better. An oversized hood moves large volumes of conditioned air out of the house and adds noise, while actual capture depends heavily on hood shape and placement.
Capture Area and Mounting Height
A hood can only exhaust what it captures. It should be at least as wide as the cooktop, and many designers add a few inches on each side, especially for islands and high-output ranges. Depth matters too, since a shallow hood can miss the front burners, where much of the cooking happens.
Manufacturers specify mounting heights, commonly around 24 to 30 inches above the cooking surface depending on the hood and range type. Raising the hood for better sightlines reduces its ability to capture rising plumes. In open-concept layouts, frequent in projects found by searching home remodeling near me Palatine, this tension between visibility and performance is a central design decision.
Ductwork: The Hidden Half of the System
Duct design affects performance as much as the fan itself:
- Rigid, smooth metal duct performs better than flexible foil duct, which creates turbulence and collects grease.
- The duct should be at least the diameter the manufacturer specifies and should never be reduced.
- Short runs with few elbows preserve airflow, because every bend adds resistance.
- The duct must end outdoors through a wall or roof cap with a backdraft damper, never in an attic, soffit or wall cavity, where grease and moisture would accumulate.
- Joints should be sealed with foil tape or mastic, not just screwed together.
Kitchen layouts are often reconfigured during kitchen remodeling near me Barrington. Moving a range to an island or another wall changes the duct path entirely, and that path is often the single biggest factor in which hood types are workable.
Makeup Air
Every cubic foot a hood pushes out of a house has to be replaced by air coming in. In tight, well-sealed homes, a powerful hood can depressurize the house. Doors may whistle, hood performance drops, and in some cases combustion gases are drawn back down the flues of water heaters or furnaces.
For this reason, the International Residential Code requires makeup air for kitchen exhaust systems capable of exhausting more than 400 CFM, in jurisdictions that have adopted that provision. Makeup air systems typically use a motorized damper interlocked with the hood, often with filtration and sometimes with heating to temper incoming winter air.
Noise and Controls
Fan noise is rated in sones, and lower numbers are quieter. Ratings are given at specific speeds, so a hood that is quiet on low can be loud at maximum. Remote or inline blowers, mounted in the attic or on an exterior wall, move the motor away from the kitchen and cut noise at the cooktop.
Variable speed controls, delay-off timers and sensors that respond to heat or humidity let the hood run when it is needed without constant adjustment. Kitchens that open onto living areas, common in home remodeling near me Rolling Meadows, benefit most from quiet operation, because a hood that does not drown out conversation actually gets used.
Maintenance
Grease filters should be cleaned regularly, and stainless steel baffle filters can usually go in a dishwasher. Charcoal filters in recirculating hoods lose effectiveness over time and need periodic replacement. Clean filters keep airflow close to the hood’s rated capacity.
A System, Not an Appliance
A range hood works as part of a system: capture area, airflow, duct design and makeup air all contribute. When these elements are planned together with the cooktop and layout, kitchen ventilation quietly does its job, keeping the air cleaner and surfaces free of grease buildup.

